How to fix the Your PC did not start correctly issue?
How to recover data from an unbootable computer efficiently and safely.
Here this article talks about the Automatic Repair, Your PC did not start correctly error as shown below.
What can I do!!!!!
There are several ways to address the Your PC did not start correctly fault signal in Windows 10.
But before you get going fixing this problem, you should recover your lost data first.
PART 1.
The detailed tutorial is as follows:
Step 1: Create a MiniTool Bootable Disk.
MiniTool Power Data Recovery TrialClick to Download100%Clean & Safe
2.
Finally, click Finish after successful burning.
Step 2: Boot Windows 10 From the MiniTool Bootable Disk.
ClickMiniTool Power Data Recoveryin the main interface of theMiniTool PE Loaderinterface.
Step 3: Recover Lost Data.
Under theLogical Drivestab, opt for drive you want to recover lost data from and clickScan.
Or you might go to theDevicestab next toLogical Drives, and choose the whole disk to scan.
While scanning, you’re able to click thePreviewbutton to preview the found files.
However, to get the best result, you should wait until the full scan finishes.
After scanning, MiniTool Power Data Recovery will list a lot of files.
Now, you might select all the files you need, and then clickSaveto store them.
it’s advisable to store all files in another drive that works properly.
Insert the Windows installation media and boot from it.
Select your language preferences, and clickNext.
Typesfc /scannowand hitEnterto run theSystem File Checker.
- reboot your PC and check whether the Your PC did not start correctly error still exists.
Insert the Windows installation media and boot from it.
Select your language preferences, and clickNext.
ClickRepair your rig>Troubleshoot>Startup configs>Restart.
Press theF4key to boot Windows into Safe Mode.
Remove the problematic driver or software in Safe Mode.
Wait for the system to restart and see if it successfully boots.
BCD is a firmware-independent database for boot-time configuration data.
It is used by Microsofts new WindowsBoot Managerand replaces the boot.ini that was used by NTLDR.
Now, you might rebuild BCD to fix your PC start-up issue by following the steps below.
Insert the Windows installation media and boot from it.
Select your language preferences, and clickNext.
After selecting language, pressShift + F10to openCommand Prompt.
Typebootrec/fixmbrand pressEnter.
Typebootrec /fixbootand pressEnter.
Typebootrec /rebuildbcdand pressEnter.
- Finally, typeexitand pressEnter.
If not, keep reading.
Therefore, you gotta shut down the early launch anti-malware protection option.
The steps are:
- SelectRestartwhen you see the following error alert:
Automatic Repair.
Your PC did not start correctly.
- Then, power cycle your system and find out if the issue has been resolved.
Here are the steps:
1.
Choose a target operating system.
Then, you will see theSystem Restoreinterface as follows.
Now, click theNextbutton to continue.
After that, you will be given detailed system restore points for you to select.
Just follow the prompts to restore the operating system.
Now, fortunately, MiniTool Partition Wizard can help you effectively rebuild MBR with ease.
Works when your system is installed on an MBR disk.
Download, install and launch MiniTool Partition Wizard Pro on a working computer.
Insert the bootable disk into your unbootable PC and start from it.
Then, choose the first option Partition Wizard to enter the main interface of MiniTool Partition Wizard.
Now, grab the target disk and click Rebuild MBR from the left panel.
- hit the Apply button to apply the changes.
In the Windows troubleshoot menu, choose toTroubleshoot>Reset this PC.
Lost data after a Windows reinstallation?
Read this post to see how to recover files after reinstalling Windows 10/11.
